User Tools

Site Tools


===== Introduction ===== [[|Tslib]] is an abstraction layer for touchscreen panel events, as well as a filter stack for the manipulation of those events. In order to display graphics using the TS-739x, Tslib has to be cross-compiled in a normal PC and then moved to the SBC. After you successfully install Tslib, you'll be able to calibrate your touchscreen and test it! I based this work on Donnal Oconnor's [[|guide]] to cross-compile and run Qt appplications on the TS-739x. I also found [[|this]] page very helpful, since I had some trouble making everything work fine. ==== Installing dependencies ==== Go ahead and install these dependencies: <code> sudo apt-get install automake libtool autoconf </code> ==== Getting Tslib ==== Download Donald O’connor’s prepatched library: <code> mkdir -p ~/project/downloads cd ~/project/downloads wget mkdir -p ~/project/sysapps cd ~/project/sysapps/ mkdir tslib cd tslib/ unzip ../../downloads/ cd tslib-1.0/ </code> Donald specifies in his TS7390 Configure file to start by typing this in the tslib-1.0 folder: <code> echo "ac_cv_func_malloc_0_nonnull=yes" > arm-linux.autogen </code> That didn’t seem to work as I was getting errors during the compilation process (you can always try both). Instead, simply (according to [[|this]] source) type: <code> export ac_cv_func_malloc_0_nonnull=yes </code> ==== Setting your cross-compiling environment ==== To do this you will have to export your cross-compiler's path: <code> export CC=/usr/local/opt/crosstool/arm-linux/gcc-3.3.4-glibc-2.3.2/bin/arm-linux-gcc export CXX=/usr/local/opt/crosstool/arm-linux/gcc-3.3.4-glibc-2.3.2/bin/arm-linux-g++ export CONFIG_SITE=arm-linux.autogen </code> ==== Configuring and installing the library ==== Specify the target you are building the library for: <code> chmod 755 ./ ./configure CC=arm-linux-gcc CXX=arm-linux-g++ PLUGIN_DIR=/usr/local/linux-arm/plugins -prefix=/usr/local/linux-arm -host=arm-linux </code> Once is done, do a make and make install: <code> make sudo make install </code> ==== Moving the library to the SBC ==== On the 739x type: <code> mkdir /usr/local/linux-arm chown -R eclipse:eclipse /usr/local/linux-arm </code> Back on the development PC, move the library to the SBC: <code> scp -r linux-arm/ eclipse@ </code> ==== Configuring Tslib ==== You need to configure the library in order for it to work (I followed the instructions available [ here]). Start by opening this file: <code> nano /root/.bashrc </code> Add the following lines at the end: <code> #added this for tslib export TSLIB_TSEVENTTYPE=H3600 export TSLIB_CONSOLEDEVICE=none export TSLIB_FBDEVICE=/dev/fb0 export TSLIB_TSDEVICE=/dev/input/event0 export TSLIB_CALIBFILE=/usr/etc/pointercal export TSLIB_CONFFILE=/usr/etc/ts.conf export TSLIB_PLUGINDIR=/usr/local/linux-arm/lib/ts export LD_LIBRARY_PATH=$LD_LIBRARY_PATH:/usr/local/linux-arm/lib/:/usr/local/lib:/usr/local/Trolltech/QtEmbedded-4.5.3-arm/lib/ export QWS_MOUSE_PROTO=Tslib </code> Ctrl X out of nano and type: <code> $ su $ cd /usr/local/linux-arm/etc $ cp ts.conf ts.conf.old $ rm ts.conf $ vi ts.conf </code> Add the following lines to the new file (do not add any blank lines!): <code> module_raw input module pthres pmin=1 module variance delta=30 module dejitter delta=100 module linear </code> Save the document, exit and type: <code> $ chmod 777 /dev/input/event0 $ cd /usr/local/linux-arm/bin $ ./ts_calibrate </code> If it doesn't run, you may need to chmod the file so it is executable: <code> $ chmod 777 ts_calibrate </code> You’re done! Test your configuration: <code> $ cd /usr/local/linux-arm/bin $ ./ts_test </code>

cross-compiling_and_installing_tslib.txt · Last modified: 2017/01/03 21:27 by admin